The Colwood Pyrography Pen Tips I Use in Wood Burning

 

In this blog I’m going to discuss the different Colwood pen tips I use in pyrography.  There are a lot of different pen tips available, but I thought it would be useful to know which pen tips I use and why.   This blog will get updated with any additional pen tips I find useful in pyrography.   

I have a YouTube video that shows this information.  Click on the image to the left to watch.

Last updated: Sept 16, 2019

First let’s talk about FT & RT pen tips and the 2 options that Colwood offers on their pen tips.   The two options are polishing and bending.

FIXED TIP OR REPLACEABLE TIPS

Colwood offers two types of pen tips: RT & FT.  RT stands for replacement tip, and FT means fixed tip.  Fixed tips are permanently secured to a pen handle.  Other than cost and the mechanics of switching out tips they work exactly the same.   

The RT pen tips have a lip on them which allows them to be pulled from the handle using a pen tip puller.   The Red arrow is pointing to the lip on a RT pen tip.  

FIXED TIP PENS (FT)

With FT you switch out the entire pen when you want to use a different tip.   This photo shows a pen with a shader pen tip on it. 

To switch out, pull on the pen to remove it from the power socket. 

Grab a new pen that has the needed tip and plug it into the power socket.     

The new pen is ready to be used and this photo shows a pen with a LSS tip on it.

REPLACEABLE TIP PENS (RT)

With RT tips you pull the old tip and replace it with the new tip you want.   In this photo I’m using a ‘tip puller’ to grab the pen tip and pull it off of the pen body.   

In this photo I’ve removed the pen tip and it’s still secure in the puller.   I have a pen tip holder Todd made me (photo at the very top), so I just drop the tip into the holder and grab the pen tip I need. 

With the pen tip in hand, I align the tabs.   

The handle has a tab that sticks out. 

 

Replaceable pen tips have a groove or channel that you align to slide over the tab on the handle.

Then I just firmly push it into the pen body and I’m ready to go.

Obviously the FT tips are more expensive as you are getting the entire pen with each one versus just the tip.  If there is a technical advantage of one style over the other I couldn’t tell you.  I personally use the RT style of tips.

You can purchase pen tips directly from Colwood (http://www.woodburning.com) or from some of the numerous sellers on the internet.

POLISHED vs UNPOLISHED

Another option Colwood offers is to have the pen tip polished.  The picture shows the J Rounded Shader unpolished (left) and polished (right).   Both work wonderfully, but the polished glides over the surface a little better and is easier to remove carbon build-up from.  Colwood charges several dollars (3$ USD as of May 2018) to polish the tips.    I have a couple of polished pen tips that I use for burning on leather.   I love how the polished pen tips glide over the leather without sticking and gumming up like the unpolished tips do.   

Is the premium for polished tips worth it?  If you are burning on leather, then absolutely.  Otherwise it becomes more of a personal choice and whether or not your budget can afford the premium.

STRAIGHT OR BENT TIPS

Colwood also to bend some of the pen tips in a 45 or 90 degree angle.   I haven’t tried the 90 degree bend, as I tend to prefer the 45.

In the photo the left pen tip is how the J shader normally ships, and I marked the pen tip with a yellow arrow.  The red arrow points to how I modified the pen tip.  I really don’t recommend this as it voids the warranty and there’s a good chance of breaking the tip off.  

This photo shows how Colwood bends the pen tip.  Notice how they bend it along the two thick connecting wires instead of the delicate pen tip end.

Should you have your pen tips bent?   If it is a shader, then I would say yes.   Note that the bending option doesn’t apply to all pen tips.  For example, I doubt anyone would want a bent micro writer pen tip. 

This photo is a screen shot from Colwood’s website showing some of the RT pen tips available along with a new handle.  This screen just shows you what type of tips are available, but you have to click on one to get more information. 

After clicking on a pen tip, this screen that appears.  For this particular tip, there aren’t any options.  If there were options then there would be drop down boxes that appear to the left of the pen tip photo.   Below the red ‘buy it now’ button is an area that tells you about the pen tip.  This one states that it comes pre-bent and polished.   

The one thing I really wish their website included are some example burn strokes.  I did send them an email about this, so I’m sure that they will jump right on it.  🙂   Ok, they might give it some small consideration.

With this particular pen tip, there is an option to have the tip polished.  The description says it comes pre-bent. 

This is a close up of the drop down box area.   The little downward pointed triangle to the right of the “not polished” will reveal the other option(s) available.   

This particular pen tip has the option for bending and polishing. 

Here’s a close up of the drop down option boxes.

HEAT SETTING

In a lot of my tutorials I will mention the heat setting I use for different pen tips.  Please keep in mind that this can vary a LOT depending on your machine, the wood you are burning on, and how old your pen tip is.   

Over time your pen tip can wear down.  Especially if you use harsh or coarse sandpaper to clean it with.   Cleaning burrs will also wear down the tip pretty quickly as I have discovered, so I don’t use the cleaning burrs anymore.   When the pen tip wears down, it gets thinner.  The thinner it is the less heat is needed.   

I tried to get a photo of my old slightly worn down tip compared to a new pristine tip, but the photos all turned out blurry.  One day I’ll manage the photo and add it to this spot. 

WARNING

A rep from Colwood told me that one of the worst things you can do with your pen tip is to allow it to get so hot it turns red.   This can reduce the life of your pen tip and possibly damage the pen tip.   

This photo is a composite showing the pen tip getting red from too much heat.   If your pen tip starts to glow, turn down the heat.  

WRITERS PEN TIPS

Writer pen tips do exactly what they say; they write.  So almost anything you can do with a black ink pen you can do with a writer.   Of the different styles of writers available, I tend to use the micro writers.  Some of the pen tips, like the two on the left, are for calligraphy styled writing.  Calligraphy is not something I do, so don’t ask me questions about it.

I use writers to burn in trace lines, draw fine lines, add tiny dots, and work in really small spots that shaders would have a hard time getting to; like tight corners.   Also I use writers to draw lizard scales, cracks, squiggly lines, and an assortment of embossed designs.  Embossed designs are designs sunk down, or carved, into the wood and then the surface around the design is burned over revealing the design.

Here I’m drawing in small scales on the face of the Collared Lizard artwork.  While you might not be able to tell it from this picture, the lizard actually turned out very nicely. 

Here’s a picture of the final product.

Here I’m using the writer to define the area between the raffia streamers on the Thunderbird Dancer Mask.

I use writers to draw lightning or crack type of lines.  Some of the small background dots were done with the writer.

Doing embossed lines is something I like to do.  This process requires you use a low heat setting and exert a lot of pressure on the pen tip to create deep, but not dark lines in the wood.   Once the design is embossed in, any residual graphite is removed, and the wood is burned over to reveal the embossed. 

Here’s a photo of the embossed design I did on the Valentine Plaque.    

Embossing works well with an assortment of burn designs like dots.  The photo below shows my starting to burn over an embossed dotted pattern I did on Mandala II.

You can create entire artwork using nothing but a writer to draw lines to give texture, color, and depth as I did in the Gingerbread House.

Super fine or small detail work is a perfect application for a writing tip.  This pictures shows me burning a thin line around the white light reflection spot on a water droplet.  I couldn’t do this with a shader.

And there are times I use a different writer, like the C writer.  Because of the style, it writes a little smoother and produces a thicker line, so I used it when creating the background floral spray on the Valentine Plaque.

Ok, so I’ve talked about what I do with writers, but what do they look like?

This is Colwood’s current style of micro writer.   It has all of the functionality of the old style, but is a much sturdier!  This is really important when doing embossed designs!   The micro writers can burn thin lines and get into really small places, but the small tip also tends to snag on grain lines.  

On many of my blogs and videos you may see the old style of micro write Colwood made.   Both styles work exactly the same, but I have bent the pen tip on this style when doing some embossing. 

This is Colwood’s regular writing pen tip called a C Writer.  I use it to write the name of the artwork on the back of the wood, some texture techniques when working mandalas, and to shade or color in small areas.  It writes smoother than the micro writer since it has a larger tip.  Another feature of the C Writer is its design allows you to get a wider range of line widths with it.   

Here’s a photo of the calligraphy pen tips (C1 & C2).  As I said before, I don’t do calligraphy and I haven’t played around with these pen tips.

This photo shows a comparison of the types of burn marks created with the writer pen tips.  As you can see, my attempt at doing a calligraphy styled letter B is terrible.   Calligraphy is an artform unto itself and one that I never learned.

SHADER PEN TIPS

Shaders are used to create the majority of the artwork I do, and while there are many different styles out there, any one of them will work.   Shaders can draw lines of various thicknesses, uniformly color an object, produce gradient shading, and create an assortment of textures.   Textures like rocks, hair, fabric, clouds, water, tree bark, fur, etc.    Watch any YouTube video on pyrography art and more than likely the artist will be using some type of shader.   

I have a particular shader I’m fond of using, the Tight Round J, but as I said before all shaders work basically the same.  The difference is the size and personal preference.  I tend to pick my shader based on the areas I’m working in.  The larger the area the larger the shader as this will cut down on the amount of time it takes to burn in the area.

I discussed how I use the shader of my preference in a fair amount of detail in another blog and I don’t want to repeat all of that here.  Instead please read “using the shader.”   

Or if you prefer, you can watch a YouTube video version I did by clicking on the image to the left.

Please note that I have purposely angled the ends of most of my shaders to make them easier for me to use.  When you purchase the tips, most of they will come straight.  For a fee you can buy them with a 45 degree angle.  I should point out that Colwood bends the two metal posts instead of the seam where the pen tip starts.

Tight Round J (1/8) Shader.  This is my primary shader. 

Its small size that allows me to get into most areas.  It is razor thin, so I can use the edge to burn fine thin lines. And, when needed I can switch to the side of the shader for bigger stuff. 

In this photo it shows two lines being burned.  The first is with the tip of the shader and the second is with the side, or long edge, of the shader.

Tight Round J Mini Shader.  I often use this shader when I’m working in smaller areas.  It does all the same things as its larger brother.

In this photo it shows two lines being burned.  The first is with the tip of the shader and the second is with the side, or long edge, of the shader.

Here’s a side-by-side photo of the Tight Round J’s together.  As you can see there isn’t a huge size difference.

S (3/16).  This is my next size up shader.  This shade has a slight curve to the end and I’ve found I like that for doing pull-away strokes.  I ended up using this pen tip a lot when I did the Crashing Ocean Waves tutorial. 

 

In this photo it shows two lines being burned.  The first is with the tip of the shader and the second is with the side, or long edge, of the shader.

D (3/16).  This particular shader is my favorite after the tight round.  I love the three different sized edges I can burn with.  I tend to use this shader when working on larger background stuff.  It produces a larger burn pattern, but it still small enough that it can easily do fine work if needed.   For me this means if I’m using this tip on the background and see something on the subject that needs touching up, I can use it.   

With this pen tip I show three lines being burned.  The three lines are burned with the different sides of the pen tip.  Using the bottom, or long, edge of the tip can produce a very wide line.

Spade (1/4).  This is my largest shader.  It’s also one of my most dangerous shaders because of the large center opening.  When I was first learning pyrography, I made a common mistake of having the heat setting too high and the spade tip sank right down into the wood leaving a “horse shoe” print embedded in the wood.  Ooops!   I use this tip almost exclusively when burning in backgrounds.  It’s large size makes it difficult for me to use when working on smaller items like eyes, ears, etc., but it’s great for darkening up large sections of background quickly.   I also love it for doing background texture like tree bark.

Another nice thing about the E spade shader is that is has a nice sharp point, so it can get into tight corners.   The first line was drawn using just the tip of the pen.  The second I decreased the angle, so more of the pen tip was in contact with the wood.  The third line is using the side of the shader.

LSS Square.  While this is called a square tip, it does have rounded corners.    I’ve used this on occasion, but not very often.   I’m super impressed with how wide of a line or band it can burn, but I can’t consistently hold the pen correctly to obtain that wide burn.

As this photo shows, the LSS tip can burn a very wide band of color.  Like I said before, I have a difficult time holding this pen tip correctly to get good contact with the wood to achieve that.   

Here is a side-by-side burn comparison of lines burned with the above shaders.

Keep in mind that the lines I burned in this example can vary a lot depending on how the pen is held.   

This photo shows test burn I did more recently using a few more shader.  Some of the pen tips I seldom, if ever, use.  

When I decided to take pyrography seriously I watched a number of YouTube videos and saw quite a few artists using spoon shaders.  I decided I better get one so I could burn great art just like they did.  Unfortunately, I hated this pen tip.  I can’t tell where I’m burning, and I find it’s hard to use the edges of it to burn thin lines.  I just felt like I had no control with it. 

As the spoon pen tip shows, what works for some doesn’t work for everyone.  If there is a shader you like, then use it!  Get super comfortable with it and your artwork will be better for it.   

As for me, I already mentioned that I use the Tight Round J for the majority of my work.  Except when I work on background stuff and then I often switch to larger pen tips.   Generally I use either the D or the E tips.   I like the D because it’s a bit larger and has 3 burning edges to choose from.  The E tip is great because of its sharp point and large burn surface.

SKEWS or KNIFE TIPS 

Knife tips, as I call them, remind me of X-acto knives and, like X-acto knives, they create thin lines.  There is an assortment of knife tip styles out there, but they all do the same basic thing; burn really thin lines.  Once I discovered this I quit using my shader to burn them.  Ok, I only use my shader if it’s a small line and I’m feeling too lazy to switch out the pen tip. 

The knife tips are fantastic for straight, cross-hatch, and semi-curved lines.  The tip tends to burn deeply into the wood, so use light pressure.    I have problems burning really curved lines with this tip and I’m sure that’s a two part problem.  1) The tip tends to burrow into the wood, so that makes it harder to curve the line.  2) I don’t practice much burning curved lines with this pen tip.

I used the knife tip to draw in the grill on the Old Truck artwork I did.

The shingle roof line and the wood boards on the Cedar CreeK Grist Mill was done using a knife tip.

Here I’m using the knife tip to draw short thin lines in a segment on Mandala III.

         

Drawing some curved lines.

MR Rounded heel.   This is pretty much the only knife tip that I use even though I have a couple others.  For me it is the easiest to control and feels the most comfortable.  The rounded or curved blade edge doesn’t drag in the wood.

Just to show a different style of knife tip, here’s a photo of the B Large point. 

And the LM Long M. 

I’ve tried using both, but because of the way I hold the pen the back edge tends to drag on the wood.  I think the problem is I’m not angling the pen tip enough.  Instead of leading with the upper point (marked with white arrow) and allowing it to do the cutting, I’m trying to use pen edges.  As a result I’m actually end up leading with the lower side (marked with yellow arrow) and it’s not sharp.  This makes it drag along the wood surface instead of cleaning cutting into it.   

This photo shows the lines created using the different knife tips.

OTHER STYLES

Large, Medium and Small Ball.   I bought the set and have found that I tend to only use the medium and large.  The small ball produces the same size as my micro writer.  

You can write, stipple (dot), and even shade with the ball tips.  They produce a very smooth burn stroke and are great for producing consistently sized dots. 

You can make the dots smaller or larger than the tip depending on how long you hold the tip onto the wood.  Quick touch and lift = smaller dot versus a Touch and Hold = larger dot.  

This photo shows some lines, dots, and squiggles that you can create with the different pen tips. 

Ball tips (think I was using the large one) are great for producing consistently sized dots.  Especially if you want larger dots.

I use ball tips to stipple texture on animal noses, like Venison, as it creates that slightly bumpy nose animals often have.

Needle Point Tip.  This pen tip has a super tiny end.  I very seldom use it except when I’m working really, really small.  The tip tends to sink quickly in the wood, so you must use really light pressure when burning.   In the numerous projects I have done, I can probably count on one hand the number of times I used this tip. 

CHISEL TIPPED

I have a couple of pen tips that have chisel tips on them.  Not sure if that’s a proper term to describe them, so let me explain.  Both the top and bottom edge of the pen are angled at the end, so it comes to a point.   I’m sure that in certain applications this feature is wonderful, but it doesn’t work for me.   When I angle the pen to use the ‘razor’ edge at the end, I get the lower chiseled edge of the triangular point instead.  I hate that, so I don’t use this style of pen tip.

Quill Tip is one of the tips I have with a chiseled edge.

Square Tip is the other one I have.  I sanded the end of the square tip to remove the chisel, so now it has a blunt end.  That didn’t help any. I could sand the tip to thin out the end, but I haven’t taken the time as I have other tips what work much better for me.

IN CONCLUSION

That’s it for this one.   Colwood makes a lot more tips than what I own, including an adaptor for using Razertip brand pen tips.  Some of Colwood’s pen tips are rather unique like the scales and circles pen tips.  I think a number of Colwood tips are used in bird decoy and other carving applications, but they have quite a few that work wonderfully in pyrography. 

One thing I have been trying to do is use some of my other pen tips.  Mostly in an effort to discover if they make certain tasks easier to do.  For example, I once burned the majority of my dark thin lines with the shader and then I discovered a knife tip.  The knife tip burned the same thickness and was so much easier to burn straight lines.

As I said in the beginning, as I learn to use more pen tips I’ll update this blog to include them.    Before then, do you have a favorite pen tip?  If so leave a comment and tell me what your favorite pen tip is and why.

Until the next blog,

Brenda

Original posted: Feb 9, 2018

Updated:  Sept 16, 2019

Want to subscribe? 

  • Click on the “Leave a Comment” field at the end of any post (blog) and a subscribe option will appear.
  • Put something in the comment field (if you put “test” or “just subscribing” I won’t make your comment public)
  • Fill in the sections for your email address and name, and then click on the “notify me of new posts via email.”
  • You will get a confirmation email from WordPress confirming you want to subscribe.
  • Click on the confirm button in that email and you’re done.

Please note that I do not send out emails.   If you have a WordPress account there is a way to subscribe within the WordPress system, but I cannot provide specifics on how it works as I don’t know.

20 thoughts on “The Colwood Pyrography Pen Tips I Use in Wood Burning

  1. Hi Brenda, quick question…I know you’ve said before that you bent your J yourself but what about D and the other shaders you use? I bought a Colwood last week and have probably more pens than i need. But my D isn’t bent. Matter of fact i think the only one that came bent is the spoon shader.

    1. Hi Kerri,
      I bent all of my shaders because I found them easier to use that way.
      I do want to mention that if you bend your own pen tips, that you will void the manufacturer warranty on them.

      On a side note, Colwood charges a premium to bend the pen tips for you. Since I’m comfortable bending my own tips, I don’t order them that way.

      If you bought your burner from someone other than Colwood, I’d be surprised if bending was even an option.

      1. Hi Brenda,
        I have a question on the bending of the shaders. You indicated that when you purchase a tip bent from Colwood that they bend the two metal posts instead of the seam where the pen tip starts. Is this different from how you bend your own? If so, is it worth getting it bent by Colwood – meaning will it still be helpful and/or make it easier to use to have it bent by them (45 angle)?

        1. Hi Peggy,

          Yes, Colwood bends them differently than I do. I bend mine at the seam where the two metal posts end and the shader begins. I got use to how this feels, so using a Colwood bent pen feels awkward to me. If I had started out with a Colwood bent tip I’m sure my way of bending would feel awkward.

          Now for the money question. Colwood is now charging $5 to bend tips. I think that is too much money for such a minor service. That is just my opinion.
          Assuming you have some pliers, it is very easy to bend your own pen tips. Just keep in mind that you will void the warranty on your pen tips if you do.

          In my Essential Pen Tips video I demonstrate how I bend my tips. The video can be accessed here: https://youtu.be/rZQkTHobQPk
          The video is broken down into chapters you can click on to quickly navigate the video. There is a chapter covering for the bending of the tips.

          Thanks for the comment and question

  2. Hi Brenda,
    Nice tutorial, thanks.
    I want to print a logo & name on each product I produce (wood & leather) do you think I’d better make a non-electric branding iron?
    Greetings

    1. Hi Ashraf,
      Hi. Thank you for the comment and compliment.
      For convenience I would think that a branding iron would be wonderful, but I couldn’t tell you if it is worth the money.
      I think it really depends on how often you would need to use it. If you only produce a few items a year, then I wouldn’t bother. If you are producing several items a month, then I would think that it would be a time saver and worth the investment.
      B

  3. Hi there, I am from South Africa and am looking to import a Colwood machine. It is very expensive to import so I hope to import The international Super Pro Deluxe Kit 220V. Replaceable Tip) . It does come with some tips. I can import an extra 10 RT tips to come in with the kit. Please can you tell me which 10 tips you would have ordered and which ones you use bent? It will really help me in making my final decision. I have watched alot of your videos and really love your style of working. You are amazing!

    1. Hi Alta,
      I had to go look up the Super Pro Deluxe kit, and it has everything you need to get started and then some.
      I only have my shader pen tips bent.
      The deluxe kit has the following 9 tips: B, C, C1, D, J, K, MC, MR, and S. Of those tips only the D, J, S are shaders.

      As for additional tips, if you’re really wanting to buy them then I’d recommend the following:
      E 1/4″ – spade shader and it’s currently Colwood’s largest shader
      Ball #3 – the largest ball tip. The smaller ball tips produce dots sizes ones make can be replicated with a writer pen tip.
      MJ or mini J – is the smallest shader they make.

      I mostly use the J, mini J, D, MC (micro writer), C writer, and E.

      Occasionally I use the ball pen tip and the rounded heel (MR). The rest of the tips in your kit I don’t use. Keep in mind that we are all different. What works well for me may not work well for you.

      Thanks for the comment!
      Brenda

  4. Hi There! First and most important, thank you for teaching me so much in the last 6 months. Your videos are awesome, the best on YouTube! I started with the simple burner from Michael’s but then I found you and your videos and the .bought a generic wire nib burner from Walmart. Then a couple of days ago I bought a double pen burner only to find out that both pens are hot and there is not an in-between switch. Another generic machine without instructions. I just didn’t think it would not have a switch? I know you like the Coleman’s but they out of my price range.
    Thanks again!
    Tam

    1. Hi Tam,
      I’m glad that you are enjoying pyrography so much that you are investing in new equipment. That is very odd both pens are hot. I’ve never heard of that before, but I would have to admit that I haven’t used anything other than the Colwood. Well, I did try a craft burner (solid tips that take 15 minutes to warm up) and I absolutely hated it. Keep in mind that it didn’t have a temperature control.

      Happy that I’ve been helpful with your learning curve.
      Thank you for the comment!
      Brenda

      1. Thanks Brenda. I have returned that generic one because I definitely did not like both pens hot at the same . I was like you in thinking they were not made that way. I hope this post helps in keeping others from making the same mistake. I did however go to Joann’s yesterday and I bought Walnut Hollow newest machine which has the wire nibs. So far I love it. It was 99.00 but with a 50% off coupon I paid 50.00.

        1. Hi Tammy,
          that’s great news. Awesome deal on the walnut hollow. I’m pretty sure that Minisa Pyrography uses Walnut Hollow, but I’m pretty sure she’s using the solid points versus the wire tips. I mention it as her work is amazing and I think it shows that it’s not so much the machine, but learning how to use the pen tips. Hope you continue to enjoy the burner and create lots of fantastic artwork with it.
          Brenda

  5. Thank you for this. I have been getting into woodburning for almost a year now and I invested in the Colwood Super Pro II. I have the replacement tips. Seeing what the tips of the pens do are really helpful. Looking forward to seeing more You Tube videos!

    1. Hi Pamela,
      Glad you found the article helpful. I love my Colwood and haven’t had any problems with it, so hopefully you will have the same positive experience. Brenda

I love hearing from you, so leave a comment.

This site uses Akismet to reduce spam. Learn how your comment data is processed.